AGILE Series

• • Different Field bus options like CANopen, PROFIBUS, Modbus
  • Optional accessories like brake resistor, mains chokes, mains filters
  • Optional Connection set for connection to PC
  
  
  Optional field bus communication:
  
  • CM-CAN: CANopen
  • CM-PDP-V1: PROFIBUS
  • CM232: Modbus ASCII & Modbus RTU for point-to-point connection
  • CM485: Modbus ASCII & Modbus RTU via RS485 connection
  • CM-DeviceNet: DeviceNet
  • CM-EtherCAT®: EtherCAT®
  • CM-PROFINET: PROFINET
  • CM-Ethernet/IP: Ethernet/IP with one usable port as end-of-line device
  • CM-Ethernet/IP-2P: Ethernet/IP with two usable ports (daisy chaining is possible)
  • CM-Modbus/TCP: Modbus/TCP with one usable port as end-of-line device
  • CM-Modbus/TCP-2P: Modbus/TCP with two usable ports (daisy chaining is possible)
  • Ethernet VABus/TCP: VABus/TCP: with one usable port as end-of-line device
  • Ethernet VABus/TCP-2P: VABus/TCP: with two usable ports (daisy chaining is possible)
  
  Optional interface for communication to PC
  
  • ASK-USB: Communication to PC via optional communication cable
  
  Optional PC software
  
  • VPlus for Windows operating system with motor setup, terminal monitor
  • Actual value window, scope function, parameter storage
  
  Accessories:
  
  • Brake resistors Type BR: The brake resistors offer an inexpensive solution to dissipate generator power that occurs at deceleration. A thermal sensor for the brake resistor protects the resistor from overheating.
  • Power choke type LCVS & LCVT: Power choke types LCVS (for single-phase power installation) and LCVT (for three-phase power installation) increase the overvoltage protection of the inverter and increase the system's EMC.
  • Power filters type FTV: Depending on the application boundaries, certain EMC levels must be achieved. The power filters are a component to improve EMC behavior in a machine installation.

• Power range (AGL402)
  0.25 - 11 kW / three-phase 320 V... 530 V / 50 - 60 Hz (± 10%)
  
  Power range (AGL202)
  0.12 - 3 kW / single-phase 200 V... 240 V / 50 - 60 Hz (± 10%)
  0.25 - 7.5 kW / three-phase 200 V ... 240 V / 50 - 60 Hz (± 10%)

• Integrated Keypad
• Integrated brake chopper
• Integrated Safe Torque Off function
• DC link connection
• 6 digital inputs, 2 multifunction A/D inputs
• 1 digital output, 1 multifunction I/O
• 1 relay output, 1 multifunction A/D/Pulse output
• Signal supply outputs: +24 V DC, + 10 V DC

+24 V DC input for electronic power supply

• Serial interfaces: RS-232, RS-485 including Modbus support

system bus

• Preset values for Bonfiglioli motors to decrease commissioning times
• Flexible assignment of digital inputs and outputs
• Energy Saving function
• Ready to use application macros
• Motor chopper function to increase braking power without brake resistors
• Power failure regulation
• Fault history
• Motor and inverter state memory
• Integrated PLC function with graphic development environment

• AGL202: 0.12 - 3 kW / single-phase 200 V... 240 V / 50 - 60 Hz (± 10%) 0.25 - 7.5 kW / three-phase 200 V ...240 V / 50 - 60 Hz (± 10%)
• AGL402: 0.25 - 11 kW / three-phase 320 V... 530 V / 50 - 60 Hz (± 10%)

• Cabinet mounting for all sizes
• Optional feed-through mounting
• Optional DIN rail mounting frame

• Motor compatibility
• Two types of motors:
• Asynchronous AC motors
• Permanent magnet synchronous (brushless) motors

Motor Control(open loop):
• Asynchronous AC motors
• Permanent magnet synchronous (brushless) motors